Condor XC-002 Ikeycutter Manually Key Cutting Machine Technical Service


Matched product:

Xhorse Condor XC-002 XC 002 Ikeycutter Manually Key Cutting Machine 3 Years Warranty

Xhorse Condor XC-002 XC 002 Ikeycutter Manually Key Cutting Machine 3 Years Warranty

US$1,199.00
  • Item No. SL355
  • Out Of Stock
Mechanical Key Cutting Machine CONDOR XC-002 with 3 years warranty
How to use Condor XC-002 Key Cutting Machine?
​​​​​​​

How to use Condor XC-002 Key Cutting Machine?

1.INSTALLING MAIN HANDLE

condor xc-002
1) Insert the bottom of main handle into installing hole, which is by the right side of the machine body. Then cover the screw cap and rotate the handle clockwise until tightened. 2) If fully tightened, the main handle should be fix at a certain position and unable to move up or down.
3) If rotate the handle 180 degrees counterclockwise, the height of tracer and cutter can be changed freely.

2 INSTALLING SUB-HANDLE
condor xc-002 guide

4) Insert the bottom of sub-handle into the installing hole, which is by the left side of the machine body. Put on the protective bushing and then plug in the lower bearing bore to avoid moving. Cover the screw cap and rotate the handle clockwise until tightened.

3.INSTALLING AND REMOVING PROBE/CUTTER
condor xc-002

1) The left one is tracer and the right one is cutter. Put the tracer and cutter into the hole and to the top limit position. Then use 2.5mm Allen wrench to turn the lock screw clockwise respectively till the tracer and cutter are both tightened.
NOTE: When using 1.5mm cutter and 2.5mm cutter, tracer and cutter must select the top with the same diameter for processing.


2) Insert the wrench into the hole, turn the lock screw counterclockwise, and then remove trace and cutter.

4. CLAMP INSTALLATION

Aim the bump (A1: underneath the clamp) at the cutting bench’s groove (A2), push toward the left until A1 and A2 (shown above) are fully overlapped. Then use 4mm Allen wrench to tighten the screw

5 PROBE/CUTTER HEIGHT LEVEL ADJUSTMENT​​​​​​​


1) When the installation finished, push the main handle. If the tracer is higher than cutter, the indicator light on the left will turn on.
2) If the tracer is lower than cutter, the indicator light on the right will turn on.
​​​​​​​
3) According to the signal of indicator light, rotate the Micro-adjuster until tracer and cutter’s tops have both touched the clamp. In other words, they are at the same height. Then two indicator lights will on, adjustment finished.

NOTE:During the height level adjustment, main clamp and sub-clamp must at the same side.

6 ROTATION SPEED ADJUSTMENT
Rotation adjustment knob locates at the right side of the machine. There are two gears to control the rotating speed of motor.

1) When the adjuster is at the neutral gear, motor stays at Turnoff mode; when it points to OFF, the light will be on, means the machine is ready to work.

2) When the adjuster points to 1, the motor rotates at a low speed, about 6000rpm; when it points to 2, the rotation speed is higher, about 8000rpm.


Condor key cutting machine Specification Comparsion:

Key cutting machine Condor XC-007

 

 

Condor XC-MINI

 

Condor XC-002

 

 

Input Voltage AC110V/220V 90V–264VAC 220VAC
Input Frequency 47~63Hz 47~63Hz 50Hz
Consume 220W 200W 200W
Packing Dimensions L460*W 520*H 620mm L450*W450*H350mm L595*W550*H375mm
Machine Dimensions L336*W 407*H490mm L265*W362*H301mm L298*W445*H525mm
Display 800*480 1024*600  
Spindle Speeds 12,000 rpm 9000rpm 8000-10000rpm
USB USB2.0 USB2.0  
Working Temperature 0~50℃ 0~50℃ 0~50℃
Humidity 10~90% 10~90% 10~90%
Net Weight  31Kg 18Kg 23Kg
Gross Weight 35Kg 22.9Kg 28Kg

 

2.Xhorse iKeycutter Condor machines Differences::

Condor XC MINI master is the mini version of Condor XC-007 machine,can replace XC-007.And both of them are automatic key cutting tool.

But the new Condor XC-002 is a manual/mechanical key cutting machine.

XC MINI has no limitation in applied voltage, while XC-007 needs setting, use with 220V voltage